Chris West - West Coast Fiero - Hardcore Hardware

Engine Hardware for 60 degree V6

WCF61 & WCF81 High Performance ENGLE CAMS

Larger View and Tech. Info.	Custom ground for West Coast Fiero, these High performance cams will drop into any 60 degree GM V6. They will fit your 2.8, 3.1 and 3.4 engine. Specially ground to maintain intake manifold vacuum at idle. Adds more than 10HP throughout the entire RPM range to approx. 6,000 RPM. This cam works well with modified 2.8 engines and especially well with 3.4 engine conversions. Valve spring replacement not necessary. Utilizes stock push rods. *Cam timing, lift and duration specifications and cam lube are packaged with each camshaft.
	(p/n EH60CAME61 or p/n EH60CAME81) - Cam	$194.00
	Eaton High performance hydraulic lifters. These are the best aftermarket lifters available anywhere. New lifters are a MUST when installing a new camshaft.
	(p/n EH60CAMELIFT) - Lifters	$110.00
	Cam Installation Kit Includes Engle WCF61 or WCF81 CAM Eaton Lifters Gasket Set Timing Chain (Kit is over 10% savings)
	(p/n EH60CAMEFKIT) - Cam kit	$395.00

Cam / Crank sensor plugs for Camaro 3400 Engine.

Cam and Crank Sensors are not used in the Fiero conversion.

These plugs will reduce the hassle of having to locate or buy sensors to fill the unused holes.

(p/n EH60CAMCSP) - Cam/crank sensor plugs

$24.00

High Performance Intake Manifold for V6 - here! now!

Larger View

This Manifold replaces the top half of the Fiero intake manifold, giving you an effective increase of 64% in the intake air flow and efficiency for highly modified V6 and 3.4 engines.

Only slight modifications to electrical are required to accomplish this install.
1. Relocation of coil pack may be necessary and is recommended in any case
    for heat reduction.
2. Removing water lines to the Throttle body and blocking off.
3. Extending vacuum lines.
4. New Air intake tubing from Holly Throttle bodies to air cleaner is provided.
5. Stock Throttle cable and cruise cable are used for this installation. Fuel
    enrichment via Computer Chip or West Coast Fiero Piggy-back computer will
    be required. O2 gauge highly recommended for tuning fuel delivery. Reverting
    back to stock is as easy as replacing the old top half of your manifold.
6. Unit comes shipped in raw aluminum ready for paint or polishing.

$700.00

Contact Chris for availability and to reserve your unit.

Fuel enrichment system
Includes complete manifold as above.
plus
Includes extra injector and Computer Controller
for the 7th injector (does NOT replace factory ECU.

$1,095.00

Throttle body and adaptor to stock Fiero intake.

$350.00

West Coast Fiero high performance Roller Rockers.

West Coast Fiero Roller Tip 1.6 to 1 Rockers will increase the valve lift on your Fiero with minimal infraction on smog. This will help increase horsepower output of your stock or modified engine. These rockers will work on your 2.8, 3.1 and 3.4 engines.

EH60CAMFRTR
$190.00
per
set of 12

West Coast Fiero full roller rockers are available in 1.6 to 1. These will greatly reduce valve train friction and increase performance and horsepower output. These will greatly valve float at higher RPM due to less valve train friction and less heat generation than conventional rockers.

EH60CAMFFRR
$332.00
per
set of 12

West Coast Fiero Roller Rocker bolts.

We are the ONLY supplier of these hard-to-find Roller Rocker Bolts. These will thread into the stock Fiero head without modifying the rocker arm stud hole. These are 10mm x 3/8" Studs.

When our supply is gone, there will be no more..

EH60CAMFRRB
$99.50
per
set of 12

West Coast Fiero Transmission Oil Cooler.
	Protect your Automatic Transmission from overheating with this racing quality Oil Cooler. Constructed in radiator style with 3/8" oil line in and out for maximum fluid flow. This unit is far superior to the factory radiator cooling system.
	(p/n EH60TOC) - Trans oil cooler	$132.00

HOME